Keeping Warm

Even though the daytime temperatures here in Northern Colorado have soared back into the 90s, there is a touch of fall in the early morning air. In my real world, our house has a fireplace with gas logs operated with a remote; now that is the Life of Riley. The Bellingham Farmhouse has two working fireplaces to keep those two rooms warm and cozy. While the fireplaces were easy to construct and install, the chimney has been such a challenge. The kit provided stencils and powder to create both the brick foundation and a stone fireplace, but the product worried me. I am coward builder, avoiding things that I perceive as too hard or complicated or beyond my limited skills, nor did I like the look of the stenciled brick. So I bought the little plaster bricks to make the fireplace, a kitchen wall, and the chimney, with crummy results because I am not a a very good brick layer or stone mason.

I have seen the work of other builders who egg carton for bricks and stone and the results look so realistic, so I know that you are asking why I didn't take that route? I may the next time, but here egg cartons are a precious commodity. We have 13 laying hens that when the universe lines up just right, they produce so many eggs that I sell them, and so I need to save my cartons. Anyway.

Here is the tale of two chimneys.

I began by cutting new chimney pieces, using 3/32 bass wood purchased at Hobby Lobby. I used the original parts that were punched out of the plywood pieces to trace the patten on new wood. Then I cut the parts out using my scroll saw.

It is very hard to get a perfectly straight cut since the scroll saw does not have a cutting guide, so I sanded the edges smooth and straight. Bass wood is a very soft wood and can easily be cut with a utility knife, but I don't always get very good results with a knife either, and this required a lot of cutting. The scroll saw is a really valuable tool to have. If you plan to be a miniature builder, doing more than one house or project, it is a great investment. Mine is an older one that I found on Craig's list. I asked my husband to change the blade and was surprised at how much better it cut.

The new pieces look very good.

Here is the original chimney all bricked. Actually, it looks pretty good. I spent a lot of time on it and it seemed such a waste not to use it. But to me, it looked tacky. Awful.

Especially this piece because I didn't know what I was doing. I tried the mortar that came with bricks. It didn't work--as you can see here. So I ordered pre-mixed mortar. Another failure.

After spoiling the smoke stack, I used a product is a silicone and brick mortar used to repair cracks in the brick mortar on a house. I liked the results, but I did such an awful job placing the bricks to begin with.

This piece doesn't look too awful, does it? I just needed to do a better job of brick laying. Next time. 

I began gluing pieces together.

Side by side the new chimney looks good.

The hardest part was rebuilding  the chimney smoke stacks that the original kit did not have. I dug into my stash of wood for small pieces to cut and found a drawer that I had made for a wall shelf that didn't work out. It was perfect then I tried to duplicate it. Finally I got right. The hours that I spent rebuilding the chimney might have been better spent. The little stack piece required a lot of sanding to get it the right size, but I was pleased with the final results. Next, I had decided to use the product that came with the kit to create a stone chimney.

The kit includes a stencil for bricks and stone. The bricks go on the foundation, while the stone goes on the chimney. I am going to paint the foundation gray to replicate a cement foundation.

The stencil is easy to apply. I tried to match the center seam, but found it impossible, but in the end it didn't make a difference the end result and overall look of the bricks.

You have to look really close to see where the seam is. 

I created two practice pieces, one unpainted and one painted.The instructions said to paint the chimney first. I had this gray paint on hand, but after I finished the project, I wish had used a darker gray, even short of being black for a better contrast.

The stone mixture is a combo of white glue (Elmer's), equal amounts of water, and essential 3-1 ration of glue to powder; however, I realized that I need much much more powder to get cake frosting consistency and then as I worked, the stone mixture began to thicken almost even to the point that was too stiff, but I was nearly done.

 

Once applied, the directions say to way no more than five minutes before removing the stencil. I liked the results, but the stone seemed too runny, so I added more powered for a thicker more frosting like stone.

Then I went to work. I used a narrow craft stick to smear on the product. The instructions will say to use a trowel, but in the absence of such a tool, I improvised. The craft stick worked perfectly.

I liked the results. Sort of. I wished that I had painted the wood darker, but I was prepared to use this chimney--then I had second thoughts. 

I did the unthinkable: asked my husband for his opinion. He has a good eye for detail--down the .1000th--he worked for 30 some years as a machinist, so I trust his judgment. He is also a perfectionist and I do value his thoughts, though I may not always listen.

I knew, too, which chimney he would choose.

\

You can see the problem in these two photos with the brick chimney.

 

That wide gap at the top. Fascia trim will hide the gap, but the top part of the chimney does not line up.

He said, "That's okay. Who will notice? Will you notice once it is all be assembled?  The lower part of the chimney is glued in place with the trim yet to be glued down. I'll wait until I begin the shingles before I guess on the trim and the top part of the chimney. I have more work to do on the smoke stack. I am going to use chalk to create soot around the outside to cover up the mortar boo-boo.

It actually looks pretty good. The stone chimney was too bland. I'll save it for another day.

The house is nearly done. I still have some trim to finish and the base to paint

This patio set is showing up all over the place. Found it at Hobby Lobby. Four pieces: Sofa, chair, side table, bench or coffee type table.

Love the dog. He is supposed to a German Short Haired pointer.

Found these cacti in the sticker scrap booking section at HL. Six to the pack. They are so cute. Perfect for an old Texas farmhouse.

So there is the tale of two chimneys. A long, grueling task to get it all sorted out and installed. I am liking the brick one. I've created a cover story: Young couple has purchased this old farm house and room by room is renovating. The original chimney will eventually need to be replaced, as the bricks continue to age and crumble. Does that work? 

Thanks so much for visiting. Leave a comment so that I know someone out there is listening--reading. 

Making Light: A New Lamp Tutorial.

I hope that I am nearing the finish line with the The Bellingham Farmhouse. I am growing weary workin on it. I glued the windows in last week and this week I'll be working on the outside trip work. The inside is looking finished, though I have the attic to do yet. I do get side tracked on making little things to compete a room, like making a lamp. Would you like to know how I made it? I'll share my project with you.


I wrote a lamp tutorial in April 2015, and you can visit that post if you like: Blue House Kitchen and Lamp Tutorial , but I think that you will enjoy my revised method best.

Items that you will need:

Wooden Spindle: Purchased at Hobby Lobby. It will have wooden pegs that will have to be removed. Next drill a hole from the top to the. The bottom also needs a channel cut for the cord to lay in. I used my dremel and placed the spindle in a small vice. You can use a hand drill to drill the hole and a craft knife hone out the top hole to make it large large enough for the crimp. When you have the hole large enough for the crimp to fit, glue it in place, then place the harp or tube over the crimp. Gluing the harp in place is optional. I didn't. PS: It is really hard to center your drilling hole, especial with the dremel.

Wire Crimp found in the jewelry findings section at Hobby Lobby. No specific size on the label other than "large."

Light: I used a candle style light that you can find at HouseWorks. It is not the one shown in the photo. As it turned out, that one was too large, so I dug in my stash and found a light, but it required splicing to a cord with a plug. Next time I will purchase the candle light--comes two to a package--with the cord attached.

Harp or Tube: JAR/JAF Miniatures is a very interesting online store, but hard to navigate, so follow these steps to find the lamp harp:

             Online Catalog: Navigate (Long scroll trip, but you will really cool things) to page p. 41
            Retail Price List: The web site says to email the company to place an order or fill out this form and mail it in with a check. I sent an email and received a prompt response.

Select these items for your 1:12 lamp: 1 R-81 Shade; 82 wheel; 83 tube or harp.

To order the parts, that's tricky too. I ended up sending an email the see how to place an orders. The lady who responded was very nice and the items arrived quickly.

jandraka@jar-jaf.com

Double sticky tape: I use really sticky carpet tape on the bottom to hold the cord in place and to secure it to the dresser top. You might also lightly sand the bottom to make a flatter, smoother surface.

Paint or stain. I used fingernail decals for decoration. Then I sprayed it with an acrylic sealer just to give it a nice sheen.

It works!